Check compatibility before delivery
Send the full appliance model and installation instructions before booking.
SAFE APPLIANCE CONNECTIONS
Gas Cooker and Hob Fitting in London
Plan a gas cooker or hob installation around the appliance, connection, ventilation and cabinetry—with gas work completed only by a suitably registered engineer.
- Appliance and installation instructions checked
- Clearances, ventilation and connection assessed
- Gas work completed by an appropriate Gas Safe engineer
15+Years of Experience
✓Multi-Trade Professionals
✓London & M25 Coverage
✓Residential & Commercial
WHAT WE CAN HELP WITH
Gas Cookers Hobs Fitting. Properly Planned.
The scope is reviewed around the property, existing condition and the result you need.
The surrounding kitchen is part of the job
Safe fitting is not just a hose or pipe connection.
Regulated work and testing
Only a Gas Safe registered engineer competent for the relevant cooker or hob work should connect, disconnect, test or commission the appliance.
GAS COOKERS HOBS FITTING LONDON
Gas Cooker and Hob Fitting in London
Check compatibility before delivery
Send the full appliance model and installation instructions before booking. Fuel type, connection position, electrical requirements, dimensions and the manufacturer’s stated clearances all matter. A new hob may not fit an existing worktop cut-out, while a freestanding cooker can conflict with nearby units or combustible finishes. Confirming these details early prevents an installer being asked to improvise outside the appliance specification.
The surrounding kitchen is part of the job
Safe fitting is not just a hose or pipe connection. The engineer must consider appliance stability, ventilation, accessible isolation, proximity to combustible materials and the suitability of the existing installation. Hobs need secure support and correct sealing as specified; cookers may require an anti-tilt device or restraint. Cabinet or worktop alteration should be planned separately and completed without undermining required clearances.
Regulated work and testing
Only a Gas Safe registered engineer competent for the relevant cooker or hob work should connect, disconnect, test or commission the appliance. Registration should be checked rather than assumed. The engineer follows current regulations and the manufacturer’s instructions, tests the installation as required and identifies defects that prevent safe commissioning. We do not provide DIY connection steps or encourage reuse of unsuitable fittings.
Discuss your property requirementsCall 020 3137 9380
CAREFUL PROPERTY WORK
Planning gas cookers hobs fitting
Replacement and removal planning
Tell us whether an old appliance requires disconnection and whether disposal is needed. The new unit should remain available with all supplied parts and documentation. If the existing gas or electrical provision is unsuitable, further work may be necessary before fitting can finish. Agreeing responsibilities for worktops, electrical circuits, delivery packaging and the redundant appliance avoids uncertainty on the day.
Planning a useful first visit
Send the appliance specification, installation diagram, worktop dimensions and photographs of the existing position. Confirm delivery timing and whether disconnection, cabinet adjustment or disposal is expected. We review that information before confirming the likely scope, while recognising that concealed conditions may only become clear on site. Please flag access limits, lease or landlord permissions and any deadline that genuinely affects the work. A clear brief helps separate the requested service from decorating, waste removal or specialist work that should be quoted independently.
A CLEAR PROCESS
From Enquiry to Completed Work
Share the details
Send the London postcode, photographs, measurements and the result you want.
Confirm the scope
The requirements, access, materials and appropriate trade are reviewed before work begins.
Complete the agreed work
The planned work is carried out carefully, with any material change explained clearly.
GAS COOKERS HOBS FITTING FAQ
Before You Book
Useful answers for planning the work.
Does a gas cooker need a Gas Safe engineer?
Yes. Connection, disconnection and other gas work must be carried out by a Gas Safe registered engineer competent for that appliance category.
Can a new hob use the old worktop opening?
Only if dimensions, support and clearances meet the new manufacturer’s instructions. Cut-out alterations should be assessed before installation.
Do gas appliances also need electricity?
Many use electricity for ignition, controls or ovens. The manufacturer’s requirements and the existing electrical provision must be checked.
Can the old flexible connection be reused?
The attending engineer decides what is suitable and compliant. Connections are not reused simply for convenience.
What if the appliance cannot be commissioned?
The engineer will explain the defect or unmet requirement. Unsafe or non-compliant installations must not be put into service until corrected.
ONE CLEAR NEXT STEP
Discuss Your Gas Cooker and Hob Fitting Requirements
Send photographs, the property location and a concise description of the gas cooker and hob fitting work. We will review the practical scope and explain what information is needed before an appointment can be confirmed.